|
| |
"A" Engine =
273, 318, ('67 and Later), 340, 360
"B" Engine =
361, 383, 400 "RB"
Engine = 413, 426wedge, 440
Crate HEMI Engine =
426, 472, 528
w/
= With
w/o = Without
Choose Your Bracket Below By Clicking On The Image For More Details,
Pictures,& To Order!
 |
This Bracket Fits B & RB Engines With Factory
A/C Style Alternator Brackets & Pulleys.
For '67-Later Cast Iron Water Pump
Housings
You Can Take That Old Factory Compressor Off & Put
This New Low HorsePower Robbing Sanden In The Same Exact Location As Your
Factory A/C Compressor! No Ad-On Pulley, Nothing But Factory!
EVEN FITS SHAKER HOODS & OTHERS
Fits:
'67 & Later 383,400, 440 with Cast
Iron Water Pump Housing.
Compressor Required: BPE6664 Sanden SD508
|
 |
This Bracket Fits B, RB,& HEMI Engines With
NON-A/C Brackets, Pulleys,& No PowerSteering
This Bracket Will Allow You To Mount A New Low
HorsePower Robbing Sanden Compressor, Where Your P.S. Is Normally Located!
The Compressor Will Line Up With Crank As The P.S. Did!
Fits:
All B/RB/Hemi, All Intakes Combo's without O.E. Power Steering.
Will Fit SOME Engines with Aftermarket Heads
(READ TECH INFO FOR MORE DETAILS)
Compressor Required:
BPE7312 Sanden SD7H "Shorty"
|
 |
This Bracket Fits B, RB, & HEMI Engines With
Factory A/C Brackets & Pulleys.
For '66-Earlier Cast Iron
Water Pump Housings
Or Aluminum Water Pump House
You Can Take That Old Factory Compressor Off
& Put This New Low HorsePower Robbing Sanden In The Exact Same Location
As Your Factory A/C Compressor. No Ad-On Pulley, Nothing But Factory
Look! Or Even Set Your HEMI
Up To Look Like It Came With Factory A/C!
EVEN FITS SHAKER HOODS & OTHERS
Fits:
Aluminum Water Pump & 1966 Earlier Cast Iron Housings
Compressor Required:
For B/RB: BPE6664 Sanden SD508 or For Hemi: BPE7312 Sanden SD7H "Shorty"
|
 |
This Bracket Fits M.P. Crate HEMI Engines or Original HEMI's with RB Damper, With
Factory A/C Pulleys & BPE 5250CHAC Alt. Brackets.
For '66-Earlier Cast Iron
Water Pump Housings
Or Aluminum Water Pump House on Hemi's
Now You Can Set A Hemi Up To Look Like A
Factory Air RB Motor! Put This New Low HorsePower Robbing Sanden In The Same Location
As A Factory A/C Compressor Would Have Been. No Ad-On Pulley, Nothing But Factory
Look!
EVEN FITS SHAKER HOODS & OTHERS
Fits:
Aluminum Water Pump Housings On Hemi's & 1966 Earlier Cast Iron Housings
On Hemi's w/RB Damper
Compressor Required:
BPE7312 Sanden SD7H "Shorty"
|
 |
This Bracket Fits B, RB,& HEMI Engines With NON-A/C Alternator Brackets
& Pulleys.
Here is Our HOTTEST Compressor Bracket Yet!
This Bracket Will Allow You To Mount A New Low HorsePower Robbing Sanden
Compressor, UNDER Your Alternator! Hidden Away From View.
Follow The Link For A Great VIDEO On This
Bracket.
Fits: B/RB/Crate Hemi Engines without Mechanical Fuel Pump and Aluminum or Cast Iron Water Pump Housings with Drivers Side Lower Radiator Hose Inlet.
Compressor Required:
BPE7312 Sanden SD7H "Shorty" |
 |
This Bracket Fits A Engines With Factory A/C
Brackets & Pulleys.
Direct Sanden Replacement Bracket for all 1970 and
Later A-Engines with Factory Installed RV2 or C171 Compressor. Works with All
Years of Intakes, Centered & Drive Side Offset Thermostat Housing Along With All LA &
Magnum Crate Engines Produced Before 2003.
Fits:
1970 Later A-Engines, Pre'03 Magnum Engines
Compressor Required:
BPE7312 Sanden SD7H "Shorty"
|
 |
This Bracket Specifically Designed For NEW
Magnum Crate Engines W/ Passenger Side Offset
Thermostat Housing, & 70-Later A-Engines
With NON-A/C Alternator Brackets & Pulleys.
Here is One Of Our HOTTEST Compressor Brackets! This
Bracket Will Allow You To Mount A New Low HorsePower Robbing Sanden Compressor,
On Your A-Engine Or New Passenger Side Offset Magnum Crate Engine, Using Only
NON-A/C Alternator Brackets & Pulleys! Works w/ or w/o P.S..
Follow The Link For A Great VIDEO On This Bracket.
Fits:
NEW Magnum Crate Engine Intakes with Passenger Side Offset
Thermostat Housing & All
1970-Later A-Engine
Compressor Required:
BPE7312 Sanden SD7H
|
 |
This Bracket Fits AKA:
"318 Wide Block"
318 Polyspherical Head 318
(2 Bolt Valve Cover Engine Only) |
|
*Works on 1957-1966 318 cu.
in. Engines
- With Out Factory Air Conditioning
- With Factory Power Steering
- With Standard Style Single Groove Alternator
* Will Not Work on LA Style 273/318/340/360 Engine (5 Bolt Valve Covers)
* Designed to Work with 2 Groove Non A/C Factory Crank Pulley
* Bracket Only Works with Sanden 7312 Compressor |
Above We Have Product Videos When You Click On Some
Brackets. Videos
Of ALL BPE PRODUCTS Coming Soon!
Contact us by E-mail at:
RB@bouchillonperformance.com
|
